Dish and Motor mount support?

[ivtec]

Originally Posted by wildshovelbill_06

latitude and longitude goes in usals[ yours]
if you got quality on that sat then you got the elevation .
i would set my dish straight at true south then u should be able to use usals to go to what ever sat you want
weather is a muck here .hope you the best

Well i changed from Cworks receiver to HDNfusion and it's easier to setup the Usuals i could move from what i thing is 61.5 to 110w after i put my Longitude and Latitude in the Usuals and with 1.2DISeqc i could pickup signal80% using circular freq 11250 and standard on 110 and 61.5 but no Quality maybe this is not the correct lnb setup,than i will try Linear next time i go on the roof today was good weather but started to rain just my luck ,i really need your help on this one,thanks in advance.i use to get dn 110,119,61.5,now since no dn I'll try FTA.

[wildshovelbill_06]

wow do be so hasty ..signal is lnb to reciver..quality is lnb to sat ie 110 61.5
now instead of changing just go to 61.5 and go out side and find that sat with the sat finder and a compass .then go inside and go to 110 if not good quality then adjust till you got it.than go inside and go to likeanother eco shit sat say 72 if you get quality on all three you got it
settings are to be 11750 circuliar lnb
now if and when u get these you will go to say gal 19 @ 97 settings will be 10750 lnb standard it is a real strong bird full of open tp,s let us know if this helps hope i answered all your questions
i think all nfusion is dead for now .dont quote me on this for im a fta only guy always was and will be from now own.
i dont care what anyone else does but it is not for me personally jmo
bill

[ivtec]

Originally Posted by wildshovelbill_06

wow do be so hasty ..signal is Ln to receiver..quality is lnb to sat ie 110 61.5
now instead of changing just go to 61.5 and go out side and find that sat with the sat finder and a compass .then go inside and go to 110 if not good quality then adjust till you got it.than go inside and go to like another Eco shit sat say 72 if you get quality on all three you got it
settings are to be 11750 circular Ln
now if and when u get these you will go to say gal 19 @ 97 settings will be 10750 lnb standard it is a real strong bird full of open tp,s let us know if this helps hope i answered all your questions
i think all nfusion is dead for now .dont quote me on this for im a fta only guy always was and will be from now own.
i dont care what anyone else does but it is not for me personally jmo
bill

My friend wildshovelbill- i was able to pull this one off i got 65.1 good signal and than went to AMC4 101w and got it too and got rid of 61.5 and kept 101 since it's where RTP the Portuguese Chan,and a few other Chan opened but there's no sound in any of them good pic but no sound i don't know why,i keep going around and around to find out on the Nfusion looking for the P-PID and AP-PID but can't find it anywhere,this is strange never saw thing like this in my life this FTA receivers keep amazing me ,maybe is because the thirt party software was installed and altered the whole Conf. of the receiver,i already did a few factory defaults but nothing,what you thing of it? it's prety shame that i got all this hard work on the roof and because of no sound ithis receiver is at no use to me ,and the wWORKS is same thing except that it gets all chan but keeps telling it's scrambled not opening any including the free ones.thanks in advance

[wildshovelbill_06]

ok, ill try but first and not being funny or anything,,,make sure the tv isnt muted or the stb .witch by default would not be when you reset it.i gotta ask a couple questions
one... did you blindscan or auto because if blindscaning it will doubleup on channels and some may work while others want.
second if you list specifis channels with the tp i will look to see if there fta or not if they are ill get you the apids and vpids..
also what kind of stb are you using and what are your settings.then ill see if i can help
bill